1. Turn off power to the garbage disposal and disconnect the down trap.
Turn off the electrical power at the fuse box or circuit breaker. Then, using adjustable pliers, disconnect the drain top from the garbage disposal waste discharge tube. (See Fig 1a)
2. Free the garbage disposal from the mounting assembly.
Support the garbage disposal with one hand and insert the end of the wrenchette or screwdriver into the right side of one mounting lug on the lower mounting ring. Lift the garbage disposal slightly and loosen the lower mounting ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is free from the mounting assembly. (See Fig 1b)
3. Disconnect the electrical.
Lay the garbage disposal on its side and remove the electrical cover plate from the bottom. Loosen the green ground screw and remove wire connectors. Disconnect garbage disposal wires from electrical supply wires. Loosen screws on the electrical clamp connector and remove wires from the garbage disposal.
4. Remove existing mounting hardware if hardware replacement needed. Otherwise skip to step 12.
To remove the existing mounting hardware, loosen the three mounting screws, pry the snap ring off with a screwdriver and remove the old mounting assembly. (See Fig 2)
5. Remove the old sink flange and putty.
Push the old sink flange up through the sink hole. Use a screwdriver or putty knife to carefully scrape all old putty from the edge of the sink hole.
6. Install the new sink flange, gasket and rings.
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4) From under the sink, slide the fiber gasket, backup flange and mounting flange over the sink flange. Hold these pieces in place.
7. Remove the dishwasher knockout plug.
If using a dishwasher, you will need to tap out the dishwasher knockout plug. Lay the garbage disposal on its side and use a screwdriver and hammer to tap it out. Next, remove the loose knockout plug from inside the garbage disposal.
8. Connect the electrical.
Turn the garbage disposal over and remove electrical cover plate. Pull out wires. Insert cable connector (not included) and run electrical cable through access hole on bottom of garbage disposal. Tighten cable connector. Push wires into garbage disposal (do not displace cardboard shield) and replace electrical cover plate.
If you have a hardwired unit and you're looking to attach a cord, you will need a power cord kit. For power cord kit installation instructions, click here.
For a garbage disposal with a factory-installed cord, simply plug in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, turn the lower mounting ring until all three tabs are locked into the mounting assembly. The garbage disposal will now hang by itself.
Lift & Latch Disposals: With both hands, lift the disposer. Slightly turn garbage disposal clockwise until all 3 mounting tabs latch over the ridges on the slide-up ramps:
10. Insert the discharge tube.
Insert the discharge tube into the discharge coupler, then slide the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler. (See Fig 7b)
11. Align the discharge tube with the drain trap.
Rotate the garbage disposal so that the discharge tube is aligned with the drain trap. If the discharge tube is too long, cut off as much as necessary. If it is too short, you can purchase an extension.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dishwasher, it may be connected through an air gap. Use a hose clamp to attach the drain hose to the dishwasher inlet. Now that everything is installed and in position, lock the garbage disposal to the sink mounting assembly using the wrenchette that came with the unit. For Evolution models, insert the Quiet Collar® Sink Baffle into the sink opening by pressing it into the sink until it snaps into place. (See Fig 7c)
13. Test the garbage disposal.
For all models, you should test for leaks at the sink flange, dishwasher, tail-pipe and mounting assembly connections. Finally, turn on the electrical breaker to test its operation.